Information
MMCX connector is one kind of RF connectors. This MMCX connector is plug/ male and straight type. It’s designed to terminate with RF Coaxial Cable by crimping to be MMCX adaptor RF cable. The applicable RF coax cable is RG174/ RG316/ RG188/ LMR100 RF coaxial cable. It is gold plating and 50 ohm impendence.
MMCX connector is small size in RF connector. MMCX Connector’s mating is snap-on type. Besides, MMCX plug/ male crimp series have straight and right angle outlook. MMCX Connector commonly is used for 0~3GHz. If you need higher working frequency or any special request about RF connector & RF cable, just please free to contact us.
MMCX connector plug straight crimp type can be terminated with RG174/ RG316/ RG188/ LMR100 RF coaxial Cable to be RF Cable assembly and charge in transmitting RF Signal in telecommunications. MMCX RF connector is most commonly used in GPS/GSM Antenna (internal or external) or GPS/GSM application these kinds of RF connectors industries.
Part Numbers
| P/N | Cable Group | Ohm |
| C05AA3F174003 C05AA3F316D03 |
RG174, RG316, RG188, LMR100 RG316D(RD316) |
50 50 |
Cable Assembly
Cable assembly Instructions Crimp type
Step1. All parts of MMCX connector are shown as the top line.
Step2. Strip the RG174 into center conductor, insulator, shielding three parts per recommended stripping dimension shown in connector spec.
Step3. Slide the ferrule onto the cable jacket.
Step4. Put the center conductor into the contact pin of MMCX plug and then solder through the hole.
Step5. Put the contact pin into main body until it stops and then spread out the shielding onto the knurled part and then
Step6. Slide the ferrule over the shielding, and proceed the first open-short test to make sure signal can transmit well.
Step7. Crimp the ferrule to let it become tighter.
Step8. Wear the heat shrink onto the ferrule and then shrink it.
Step9. Do the open-short test of every cable assembly before QC examination.
Specification
MMCX Connector Specification
| Electrical | |
| Impedance | 50 ohm |
| Frequency range | 0 ~ 6 GHz |
| VSWR | Straight type ≤ 1.3 max. |
| R/A type ≤ 1.5 max. | |
| Dielectric withstanding voltage | 500 V rms |
| Working voltage0 | 170 V rms |
| Center contact resistance | ≤ 5.0 mΩ (Milliohms max.) |
| Outer contact resistance | ≤ 2.5 mΩ (Milliohms max.) |
| Insulation resistance | ≥ 103 MΩ (Megohms min.) |
| Mechanical | |
| Coupling | Lock-snap |
| Contact Retention | 2.3 lbs min. |
| Mating Durability | 500 cycles min. (For Beryllium copper contact only) |
| Environmental | |
| Temperature Range | Teflon −65ºC ~ +155 ºC |
| Vibration | MIL-STD-202 Meth. 204 |
| Corrosion resistance | MIL-STD-202 Meth. 101 |
| Materials | |
| Body, coupling nut | Brass |
| Insulator | Teflon |
| Center contact | Brass for male, |
| Beryllium copper for female | |
| Crimping sleeve | Annealed Brass |
| Body plating | Gold (Ag) |
| Center contact plating | Gold (Ag) |
Note: These characteristics are typical and may not apply to all connectors.
